Results 1 to 5 of 5

Thread: Miss Mermaid update

  1. #1
    Inactive Member Robert T's Avatar
    Join Date
    April 17th, 2006
    Posts
    4
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    I disassembled Miss Mermaid this weekend and found a substantial amount of rust. Of course being underwater for three weeks did'nt help. Most of the rust is surface rust, no big concern. Sandblasting will take care of that. The concern now is the outer stove insulation box which holds the rockwool is in bad shape. The rockwool held the water and now the metal is rusted out in parts. Is it possible to cut the bad section out, fabricate a new piece of sheet metal and weld it in place.

    The Service Manual I purchased was definitely helpful.

  2. #2
    Inactive Member RobbiQuest's Avatar
    Join Date
    December 16th, 2005
    Posts
    323
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Robert, unless your stove has particular sentimental value, Joe might have a good point.

    One option could be to buy a similar stove and just replace the panels with your porcelain panels (since it looks like your panels are yellow, right?) You live in a Chambers-rich area (lots of them in LA), so you shouldn't have any problem finding one with chipped porcelain for a song.

    Something to consider, anyway.

    <font color="#FFFFFF" size="1">[ May 08, 2006 09:22 AM: Message edited by: RobbiQuest ]</font>

  3. #3
    Inactive Member Joe Pieweed's Avatar
    Join Date
    September 27th, 2005
    Posts
    232
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Oh, Robert. this sounds like a tough case. If I were in your shoes, I'd consider getting another stove for a good inner works with dry rockwool.

    Good luck.

    Joe P.

  4. #4
    Inactive Member berlyn's Avatar
    Join Date
    March 31st, 2004
    Posts
    516
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    RobertT.

    I third that suggestion!! [img]graemlins/thumbs_up.gif[/img]
    Keep the panels and other salvageable parts & interchange them with a white interior.
    That would be so much easier!!
    A yellow Chambers is a sought after color.Along with green & blue. Whites are all around easiest to find. A red Chambers is just too die for!!

    Just our thoughts,
    Berlyn

  5. #5
    Inactive Member chipperhiker's Avatar
    Join Date
    October 26th, 2005
    Posts
    431
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    I was thinking the same thing, Robert. You could probably find a white stove with an intact frame, etc. relatively cheaply, especially if it had chipped porcelain.

    Then, just rotate the nice yellow panels and pretty dials off Miss Mermaid onto the solid frame. You'd be in good shape, minus the difficulties of replacing the rockwool and dealing with a stove frame with real problems. You would just be combining the best parts of two damaged stoves into one solid beauty!

    As Lowracer put it once, "Rust never sleeps."

    -Jenn

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •